si poder entrar al router no podras abrir los puertos y si el firmware esta modificado
para q la configuracion no este en el puerto 80
o q este cerrada o similares
la unica opcion es el soporte tecnico del isp
o cambiar el router por un cablemodem y poner detras otro equipo en caso de ser necesario

lo q ya no fuinciona q antes funcionaba es q sacabas el cable, reiniciabas el moden y entrabas a 192.168.0.1 parece q faibertel se dio con la suya y toco algo… esa manera ya no funciona saben de algun otra?

prueba a poner manualmente los modos del modem o mira con el router de ono q tipo de sincronizacion tienes
si es adsl2+ si es g-dmt o asi y ponlo en ese modo solo a ver si es capaz de aguantar el sincronismo
es lo unico q se me ocurre ahora

Pongo la salida del “debug atm events”. Verás como detecta la línea, velocidad, etc, pero acaba dando un error y se reinicia todo el rato la sincronización. A ver si me podeis ayudar. Gracias.

*Mar 1 04:54:30.247: ATM0: atmsar_1a_reset
*Mar 1 04:54:30.247: ATM0: atmsar_get_plim_info
*Mar 1 04:54:30.247: ATM0:atmsar_update_plimtype
*Mar 1 04:54:30.247: ATM0 atmsar_1a_reset: PLIM type is 18, Rate is 4608Mbps
*Mar 1 04:54:30.247: ATM0 atmsar_1a_shutdown: state=4
*Mar 1 04:54:30.247: ATM0: atmsar_shutdown, newstate = 0
*Mar 1 04:54:30.247: DSL: SET:
*Mar 1 04:54:30.247: Resetting ATM0
*Mar 1 04:54:30.247: atmsar_1a_config(ATM0)
*Mar 1 04:54:30.247: atmsar_1a_enable(ATM0)
*Mar 1 04:54:30.247: ATM0: atmsar_init
*Mar 1 04:54:30.247: ATM0 atmsar_update_us_bandwidth(): upstream bw =4608 Kbps
*Mar 1 04:54:30.743: (ATM0)1a_enable: delay activation of vcd=2, vc=0x8310EF58
*Mar 1 04:54:30.747: DSL: SM:
*Mar 1 04:54:30.819: DSL: SM:
*Mar 1 04:54:30.819: DSL(ATM0): Downloading init_AMR-3.0.014_no_bist.bin
*Mar 1 04:54:30.827: DSL:(ATM0) Downloaded 2 blocks… Finished!
*Mar 1 04:54:30.827: DSL(ATM0): Sent command 0×14
*Mar 1 04:54:32.247: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 04:54:32.247: atmsar_atm_lineaction(ATM0): state=0
*Mar 1 04:54:32.827: DSL(ATM0): Received response: 0×80
*Mar 1 04:54:32.827: DSL: SM:
*Mar 1 04:54:32.827: DSL(ATM0): Downloading AMR-3.0.014.bin
*Mar 1 04:54:32.855: DSL(ATM0): Downloaded 100 blocks
*Mar 1 04:54:32.887: DSL(ATM0): Downloaded 200 blocks
*Mar 1 04:54:32.919: DSL(ATM0): Downloaded 300 blocks
*Mar 1 04:54:32.951: DSL(ATM0): Downloaded 400 blocks
*Mar 1 04:54:32.983: DSL(ATM0): Downloaded 500 blocks
*Mar 1 04:54:33.011: DSL(ATM0): Downloaded 600 blocks
*Mar 1 04:54:33.047: DSL(ATM0): Downloaded 700 blocks
*Mar 1 04:54:33.079: DSL(ATM0): Downloaded 800 blocks
*Mar 1 04:54:33.111: DSL(ATM0): Downloaded 900 blocks
*Mar 1 04:54:33.143: DSL(ATM0): Downloaded 1000 blocks
*Mar 1 04:54:33.171: DSL(ATM0): Downloaded 1100 blocks
*Mar 1 04:54:33.203: DSL(ATM0): Downloaded 1200 blocks
*Mar 1 04:54:33.239: DSL(ATM0): Downloaded 1300 blocks
*Mar 1 04:54:33.267: DSL(ATM0): Downloaded 1400 blocks
*Mar 1 04:54:33.299: DSL(ATM0): Downloaded 1500 blocks
*Mar 1 04:54:33.331: DSL(ATM0): Downloaded 1600 blocks
*Mar 1 04:54:33.363: DSL(ATM0): Downloaded 1700 blocks
*Mar 1 04:54:33.395: DSL(ATM0): Downloaded 1800 blocks
*Mar 1 04:54:33.427: DSL(ATM0): Downloaded 1900 blocks
*Mar 1 04:54:33.459: DSL(ATM0): Downloaded 2000 blocks
*Mar 1 04:54:33.491: DSL(ATM0): Downloaded 2100 blocks
*Mar 1 04:54:33.523: DSL(ATM0): Downloaded 2200 blocks
*Mar 1 04:54:33.551: DSL(ATM0): Downloaded 2300 blocks
*Mar 1 04:54:33.583: DSL(ATM0): Downloaded 2400 blocks
*Mar 1 04:54:33.615: DSL(ATM0): Downloaded 2500 blocks
*Mar 1 04:54:33.651: DSL(ATM0): Downloaded 2600 blocks
*Mar 1 04:54:33.679: DSL(ATM0): Downloaded 2700 blocks
*Mar 1 04:54:33.711: DSL(ATM0): Downloaded 2800 blocks
*Mar 1 04:54:33.743: DSL(ATM0): Downloaded 2900 blocks
*Mar 1 04:54:33.775: DSL(ATM0): Downloaded 3000 blocks
*Mar 1 04:54:33.807: DSL(ATM0): Downloaded 3100 blocks
*Mar 1 04:54:33.843: DSL(ATM0): Downloaded 3200 blocks
*Mar 1 04:54:33.871: DSL(ATM0): Downloaded 3300 blocks
*Mar 1 04:54:33.903: DSL(ATM0): Downloaded 3400 blocks
*Mar 1 04:54:33.935: DSL(ATM0): Downloaded 3500 blocks
*Mar 1 04:54:33.967: DSL(ATM0): Downloaded 3600 blocks
*Mar 1 04:54:33.999: DSL(ATM0): Downloaded 3700 blocks
*Mar 1 04:54:34.031: DSL(ATM0): Downloaded 3800 blocks
*Mar 1 04:54:34.063: DSL(ATM0): Downloaded 3900 blocks
*Mar 1 04:54:34.095: DSL(ATM0): Downloaded 4000 blocks
*Mar 1 04:54:34.127: DSL(ATM0): Downloaded 4100 blocks
*Mar 1 04:54:34.131: DSL:(ATM0) Downloaded 4121 blocks… Finished!
*Mar 1 04:54:34.131: DSL(ATM0): Sent command 0×14
*Mar 1 04:54:36.132: set tx_gain_offset to 0
*Mar 1 04:54:36.132: set rx_gain_offset to 0
*Mar 1 04:54:36.132: set target_noise_margin_offset to 0
*Mar 1 04:54:36.132: set max_bits_tone_limit to 15
*Mar 1 04:54:36.132: changed current state to do open!!
*Mar 1 04:54:36.132: DSL: SM:
*Mar 1 04:54:36.132: DSL(ATM0): Send ADSL_OPEN command.
*Mar 1 04:54:36.132: DSL(ATM0): Using preferred open mode
*Mar 1 04:54:36.132: DSL(ATM0): Using ITU sync first for 5 secs, then ANSI/ITU sync alternatively for 2 secs
*Mar 1 04:54:36.132: DSL(ATM0): Using subfunction 0×0
*Mar 1 04:54:36.132: LOCAL:Max noise margin for power cutoff 31
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×5
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×9
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×1
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×0
*Mar 1 04:54:36.132: DSL(ATM0): Sent extended command 0×3
*Mar 1 04:54:38.632: DSL(ATM0): 1: Modem state = 0×8
*Mar 1 04:54:41.132: DSL(ATM0): 2: Modem state = 0×8
*Mar 1 04:54:42.765: DSL(ATM0): Received response: 0×22
*Mar 1 04:54:42.765: DSL(ATM0): Open failed: Error in early non-CRC message or in first CRC-covered message — retrying
*Mar 1 04:54:42.765: DSL(ATM0): sleep 5 seconds
*Mar 1 04:54:47.765: DSL(ATM0): Send ADSL_OPEN command.
*Mar 1 04:54:47.765: DSL(ATM0): Using preferred open mode
*Mar 1 04:54:47.765: DSL(ATM0): Using ITU sync first for 5 secs, then ANSI/ITU sync alternatively for 2 secs
*Mar 1 04:54:47.765: DSL(ATM0): Using subfunction 0×0
*Mar 1 04:54:47.765: LOCAL:Max noise margin for power cutoff 31
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×5
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×9
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×1
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×0
*Mar 1 04:54:47.765: DSL(ATM0): Sent extended command 0×3
*Mar 1 04:54:50.265: DSL(ATM0): 1: Modem state = 0×9
*Mar 1 04:54:52.766: DSL(ATM0): 2: Modem state = 0×8
*Mar 1 04:54:55.266: DSL(ATM0): 3: Modem state = 0×8
*Mar 1 04:54:57.766: DSL(ATM0): 4: Modem state = 0×8
*Mar 1 04:55:00.267: DSL(ATM0): 5: Modem state = 0×9
*Mar 1 04:55:00.339: DSL(ATM0): Received response: 0×22
*Mar 1 04:55:00.339: DSL(ATM0): Open failed: Error in early non-CRC message or in first CRC-covered message — retrying

Pongo la salida del “debug atm events”. Verás como detecta la línea, velocidad, etc, pero acaba dando un error y se reinicia todo el rato la sincronización. A ver si me podeis ayudar. Gracias.

*Mar 1 04:54:30.247: ATM0: atmsar_1a_reset
*Mar 1 04:54:30.247: ATM0: atmsar_get_plim_info
*Mar 1 04:54:30.247: ATM0:atmsar_update_plimtype
*Mar 1 04:54:30.247: ATM0 atmsar_1a_reset: PLIM type is 18, Rate is 4608Mbps
*Mar 1 04:54:30.247: ATM0 atmsar_1a_shutdown: state=4
*Mar 1 04:54:30.247: ATM0: atmsar_shutdown, newstate = 0
*Mar 1 04:54:30.247: DSL: SET:
*Mar 1 04:54:30.247: Resetting ATM0
*Mar 1 04:54:30.247: atmsar_1a_config(ATM0)
*Mar 1 04:54:30.247: atmsar_1a_enable(ATM0)
*Mar 1 04:54:30.247: ATM0: atmsar_init
*Mar 1 04:54:30.247: ATM0 atmsar_update_us_bandwidth(): upstream bw =4608 Kbps
*Mar 1 04:54:30.743: (ATM0)1a_enable: delay activation of vcd=2, vc=0x8310EF58
*Mar 1 04:54:30.747: DSL: SM:
*Mar 1 04:54:30.819: DSL: SM:
*Mar 1 04:54:30.819: DSL(ATM0): Downloading init_AMR-3.0.014_no_bist.bin
*Mar 1 04:54:30.827: DSL:(ATM0) Downloaded 2 blocks… Finished!
*Mar 1 04:54:30.827: DSL(ATM0): Sent command 0×14
*Mar 1 04:54:32.247: %LINK-3-UPDOWN: Interface ATM0, changed state to down
*Mar 1 04:54:32.247: atmsar_atm_lineaction(ATM0): state=0
*Mar 1 04:54:32.827: DSL(ATM0): Received response: 0×80
*Mar 1 04:54:32.827: DSL: SM:
*Mar 1 04:54:32.827: DSL(ATM0): Downloading AMR-3.0.014.bin
*Mar 1 04:54:32.855: DSL(ATM0): Downloaded 100 blocks
*Mar 1 04:54:32.887: DSL(ATM0): Downloaded 200 blocks
*Mar 1 04:54:32.919: DSL(ATM0): Downloaded 300 blocks
*Mar 1 04:54:32.951: DSL(ATM0): Downloaded 400 blocks
*Mar 1 04:54:32.983: DSL(ATM0): Downloaded 500 blocks
*Mar 1 04:54:33.011: DSL(ATM0): Downloaded 600 blocks
*Mar 1 04:54:33.047: DSL(ATM0): Downloaded 700 blocks
*Mar 1 04:54:33.079: DSL(ATM0): Downloaded 800 blocks
*Mar 1 04:54:33.111: DSL(ATM0): Downloaded 900 blocks
*Mar 1 04:54:33.143: DSL(ATM0): Downloaded 1000 blocks
*Mar 1 04:54:33.171: DSL(ATM0): Downloaded 1100 blocks
*Mar 1 04:54:33.203: DSL(ATM0): Downloaded 1200 blocks
*Mar 1 04:54:33.239: DSL(ATM0): Downloaded 1300 blocks
*Mar 1 04:54:33.267: DSL(ATM0): Downloaded 1400 blocks
*Mar 1 04:54:33.299: DSL(ATM0): Downloaded 1500 blocks
*Mar 1 04:54:33.331: DSL(ATM0): Downloaded 1600 blocks
*Mar 1 04:54:33.363: DSL(ATM0): Downloaded 1700 blocks
*Mar 1 04:54:33.395: DSL(ATM0): Downloaded 1800 blocks
*Mar 1 04:54:33.427: DSL(ATM0): Downloaded 1900 blocks
*Mar 1 04:54:33.459: DSL(ATM0): Downloaded 2000 blocks
*Mar 1 04:54:33.491: DSL(ATM0): Downloaded 2100 blocks
*Mar 1 04:54:33.523: DSL(ATM0): Downloaded 2200 blocks
*Mar 1 04:54:33.551: DSL(ATM0): Downloaded 2300 blocks
*Mar 1 04:54:33.583: DSL(ATM0): Downloaded 2400 blocks
*Mar 1 04:54:33.615: DSL(ATM0): Downloaded 2500 blocks
*Mar 1 04:54:33.651: DSL(ATM0): Downloaded 2600 blocks
*Mar 1 04:54:33.679: DSL(ATM0): Downloaded 2700 blocks
*Mar 1 04:54:33.711: DSL(ATM0): Downloaded 2800 blocks
*Mar 1 04:54:33.743: DSL(ATM0): Downloaded 2900 blocks
*Mar 1 04:54:33.775: DSL(ATM0): Downloaded 3000 blocks
*Mar 1 04:54:33.807: DSL(ATM0): Downloaded 3100 blocks
*Mar 1 04:54:33.843: DSL(ATM0): Downloaded 3200 blocks
*Mar 1 04:54:33.871: DSL(ATM0): Downloaded 3300 blocks
*Mar 1 04:54:33.903: DSL(ATM0): Downloaded 3400 blocks
*Mar 1 04:54:33.935: DSL(ATM0): Downloaded 3500 blocks
*Mar 1 04:54:33.967: DSL(ATM0): Downloaded 3600 blocks
*Mar 1 04:54:33.999: DSL(ATM0): Downloaded 3700 blocks
*Mar 1 04:54:34.031: DSL(ATM0): Downloaded 3800 blocks
*Mar 1 04:54:34.063: DSL(ATM0): Downloaded 3900 blocks
*Mar 1 04:54:34.095: DSL(ATM0): Downloaded 4000 blocks
*Mar 1 04:54:34.127: DSL(ATM0): Downloaded 4100 blocks
*Mar 1 04:54:34.131: DSL:(ATM0) Downloaded 4121 blocks… Finished!
*Mar 1 04:54:34.131: DSL(ATM0): Sent command 0×14
*Mar 1 04:54:36.132: set tx_gain_offset to 0
*Mar 1 04:54:36.132: set rx_gain_offset to 0
*Mar 1 04:54:36.132: set target_noise_margin_offset to 0
*Mar 1 04:54:36.132: set max_bits_tone_limit to 15
*Mar 1 04:54:36.132: changed current state to do open!!
*Mar 1 04:54:36.132: DSL: SM:
*Mar 1 04:54:36.132: DSL(ATM0): Send ADSL_OPEN command.
*Mar 1 04:54:36.132: DSL(ATM0): Using preferred open mode
*Mar 1 04:54:36.132: DSL(ATM0): Using ITU sync first for 5 secs, then ANSI/ITU sync alternatively for 2 secs
*Mar 1 04:54:36.132: DSL(ATM0): Using subfunction 0×0
*Mar 1 04:54:36.132: LOCAL:Max noise margin for power cutoff 31
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×5
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×9
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×1
*Mar 1 04:54:36.132: DSL(ATM0): GPCI 0×0
*Mar 1 04:54:36.132: DSL(ATM0): Sent extended command 0×3
*Mar 1 04:54:38.632: DSL(ATM0): 1: Modem state = 0×8
*Mar 1 04:54:41.132: DSL(ATM0): 2: Modem state = 0×8
*Mar 1 04:54:42.765: DSL(ATM0): Received response: 0×22
*Mar 1 04:54:42.765: DSL(ATM0): Open failed: Error in early non-CRC message or in first CRC-covered message — retrying
*Mar 1 04:54:42.765: DSL(ATM0): sleep 5 seconds
*Mar 1 04:54:47.765: DSL(ATM0): Send ADSL_OPEN command.
*Mar 1 04:54:47.765: DSL(ATM0): Using preferred open mode
*Mar 1 04:54:47.765: DSL(ATM0): Using ITU sync first for 5 secs, then ANSI/ITU sync alternatively for 2 secs
*Mar 1 04:54:47.765: DSL(ATM0): Using subfunction 0×0
*Mar 1 04:54:47.765: LOCAL:Max noise margin for power cutoff 31
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×5
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×9
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×1
*Mar 1 04:54:47.765: DSL(ATM0): GPCI 0×0
*Mar 1 04:54:47.765: DSL(ATM0): Sent extended command 0×3
*Mar 1 04:54:50.265: DSL(ATM0): 1: Modem state = 0×9
*Mar 1 04:54:52.766: DSL(ATM0): 2: Modem state = 0×8
*Mar 1 04:54:55.266: DSL(ATM0): 3: Modem state = 0×8
*Mar 1 04:54:57.766: DSL(ATM0): 4: Modem state = 0×8
*Mar 1 04:55:00.267: DSL(ATM0): 5: Modem state = 0×9
*Mar 1 04:55:00.339: DSL(ATM0): Received response: 0×22
*Mar 1 04:55:00.339: DSL(ATM0): Open failed: Error in early non-CRC message or in first CRC-covered message — retrying

El modem está levantado y con el dsl en auto. Ayer vi que el status de la ATM0 se quedaba en “initializing”. Si hago un “show atm events” puedo ver como envía al modem continuamente la orden 0×08 y al final me informa que de la conexión no se puede establecer. No se que puede pasar … Aún estando en este estado si hago “show int atm0″ veo que me detecta la velocidad de la línea a 4608, pero entiendo que no establece el enlace con el servidor.
Intentaré hacer una subinterfaz, aunque el ejemplo que me adjuntas es pppoe y esta ya había hecho funcionar en otros routers.
Gracias.

ya he editado el titulo
a ver si con esto te orientas
foro/routers-adsl/otros-routers/router-cisco-857w-no-navega-internet-t99249.html
confirma q tienes el modem levantado y en modo de modulacion auto

la velocidad de adsl llega hasta 8 y 1 pero para esas velocidades se puede usar adsl adsl2 o adsl2+ indistintamente

Perdón, es un 877 … y la línea es adsl (4000 kbps / 608 kbps)

Buenas a todos,
estoy intentando configurar una conexión adsl de ONO pero no hay manera de que la línea ATM se levante. Lo he probado de varias formas y al final he seguido la explicación de cisco sin éxito alguno. Adjunto la running-config:

Current configuration : 1287 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
logging message-counter syslog
!
no aaa new-model
!
!
dot11 syslog
ip source-route
!
!
ip cef
!
!
!
!
!
!
!
archive
log config
hidekeys
!
!
!
!
!
interface ATM0
no ip address
ip nat outside
ip virtual-reassembly
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
dsl enable-training-log
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface Vlan1
ip address 197.129.17.100 255.255.255.0
ip nat inside
ip virtual-reassembly
!
interface Dialer0
ip address negotiated
ip mtu 1492
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname XXXXXX@XXXXXXX
ppp chap password 0 AAAAAAAAA
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
!
ip nat inside source list 1 interface Dialer0 overload
!
access-list 1 permit any
dialer-list 1 protocol ip permit
!
!
!
!
control-plane
!
!
line con 0
no modem enable
line aux 0
line vty 0 4
login
!
scheduler max-task-time 5000
end

No se en que me puedo estar equivocando. La info del comando “sh dsl int atm0″:
ATM0
Alcatel 20190 chipset information

Line has not yet been activated.

Modem Status: Down (DMTDSL_DO_OPEN)
DSL Mode: Unknown
Interrupts: 283922 (0 spurious)
PHY Access Err: 0
Activations: 0
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-3.0.014_no_bist.bin
Operation FW: AMR-3.0.014.bin
FW Source: embedded

La info de “sh ip int br”:
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES unset down down
Dialer0 unassigned YES manual up up
FastEthernet0 unassigned YES unset up down
FastEthernet1 unassigned YES unset up down
FastEthernet2 unassigned YES unset up down
FastEthernet3 unassigned YES unset up down
NVI0 unassigned NO unset up up
Virtual-Access1 unassigned YES unset up up
Vlan1 197.129.17.100 YES manual up down

Espero me puedan ayudar. Muchas gracias!

hola, si te vale de respuesta por mi experiencia. Yo tengo 50mg y tv, y desde el primer dia me pusieron el Cisco epc3000, y el Dlink Dir-655, y chico eso es mano de santo, todo lo contrataso desde el primer momento y por ahora y tocare madera, va muy bien, del otro router que comentas creo que falla mucho.ok.
Saludos y a disfrutarlo.